Audi Tuning | VW Tuning

Achtuning wants to credit Jamie Everett for this set of fantastic rolling shots captured of our Achtuning A3 Project! These shots were taken on the way to the WaterWerks 2009 event held at Cheney Stadium in Tacoma, WA.

The Achtuning A3 project is proud to show off high quality performance parts from H&R, APR, StopTech, and Hartmann’s Forged Split-7 Wheels. Other than the factory votex kit painted by Dreamwerks Custom Paint in Monroe, WA little has been done to further enhance the exterior appeal of the car yet it turns heads on just about every corner. We are very pleased with how the project turned out.

Thank you Jamie, Hans, Andy, APR, H&R, and StopTech!

Last Friday we threw on the H&R Premium Coil-Over Suspension on each corner of the Achtuning A3 project, bringing the car closer to the ground where it belongs. More importantly of course, we’ll be able to handle local roads and tracks with ease and hug our 19″ Hartmann Forged Split-7 Wheels with the better performing suspension.

We’ve also got a new rear sub frame brace we’re testing out. This triangular piece mounts between the rear control arms with no extra drilling or modification and offers better handling and steering response in cornering. We’ll add a rear anti-roll bar the next chance we get to further eliminate body roll and try to neutralize some of the A3′s under-steer characteristics.

We took her out for a spin and the motor is putting down some good power! Clearly the stock 17s with all-season tires weren’t going to cut it and we immediately noticed severe brake fade after a few hard runs so brakes were definitely going to be the next order of business.

The StopTech 328x28mm, 4-piston Big Brake Kit ended up on the car yesterday and look fantastic with the red and black H&R suspension components!

Brake clearance was tight with the new 4-piston calipers but it was just enough to make things fit the way it needed…

We’re still undecided on the final wheel finish so for now we’ll keep them polished. Front bumper is also back on and a Votex kit might be the next thing added to our Achtuning A3 project.

“Motor #2″, you ask?

Here sat the Achtuning A3 project as we had pulled it out for its maiden voyage with the completion of the S3 Conversion to the 2.0T engine. We wanted to make sure it was properly warmed up before seeing how much power the turbo upgrade would produce.

Unfortunately our test-run didn’t last long… It seems the high-mileage motor in the A3 we picked up wasn’t a clean-slate, “blank canvas” as we had hoped after all as it gave up on us within 5-minutes of our run. As we knew there had to be underlying issues with the motor in our A3, we decided to pull it.

We found unusually excessive carbon build-up on the valves along with a few other things we noticed indicating this motor had been tampered with before – and not necessarily in a good way.

Despite the small hiccup, we’re moving forward with the A3 project but with a slightly different direction this time…

We’re building up two motors for this A3 now, one to continue our “Edition 30″/S3 Conversion and another, more powerful motor.  It’s been (thankfully) a busy couple of weeks since and despite our hectic schedule, we’re pleased with the progress of our Achtuning A3 project. Everything that was added to engine number-one as far as the S3-Conversion has been reinstalled on engine number-two.

Today we’ve got the front end all wrapped up and we’ll begin to work on other areas of the car. We also had to take our Neuspeed P-Flow and modify it due to the relocation of the electronic DV (diverter valve) on the S3-conversion.

Then some wrinkle-finish paint to touch up the new addition…

And the final product!

We still have quite a ways to go but considering circumstances we couldn’t be in a better position.

Dreamwerks completed the Votex kit for the Achtuning A3 Project and we couldn’t be happier with the results!

The kit will go on the car within the next couple of weeks as they will likely be the last itmes to go on the car but we’re confident the look will be just right! Thanks Hans and Andy for your diligent and quality work!

More parts trickle in for the Achtuning A3 Project – today from StopTech we received a 328x28mm, 4-piston Big Brake Kit.

We picked up some stainless steel lines as well to complete the front brake upgrade for the A3.

Starting at $1995…

We dropped off the Votex kit for the Achtuning A3 Project at Dreamwerks yesterday! Known for their excellent quality and passion for everything European, we knew our OE body kit was in good hands…

Our very close friends at H&R sent us a set of their Premium Coil-Overs for our Audi A3 project.

H&R’s Premium line offers ultra-lightweight performance with these aluminum-bodied dampers with a reduced weight of up to 40% from factory suspension components, further assisting us in the reduction of unsprung weight. Each shock is “tuned with a progressive rate spring that is engineered from its inception to work with the shock’s valving, creating a finely tuned suspension system.” The coil-over kit has a drop range of 1.0 to 2.5 inches and are hard-anodized in black – perfectly matching our Achtuning theme.